Para-fine Chem Industries
Home About Us Our Products Contact Us Enquiry

Para-fine Chem Industries

Home » SPECIALTY CHEMICALS

SPECIALTY CHEMICALS

Speciality Chemicals requirement by the industry is growing day by day with the rapid industrialization.  Moresoever each industry looks for very specific requirements and the need for customization comes into prominence.  With the growing awareness of the danger to the environment,  customers are also on the lookout for more eco-friendly and bio-degradable products and products that are also  less hazardous to the employees  during the production process.

It is here that we play a vital role in providing the industry very specific requirement developed in short duration of time. The product range offered is quite wide in terms of application and covers a large spectrum of the industry.

PCB Flux Remover

Many times in Electronic Industries, after the PCB Assembly, a mixture of IPA & TCE is used in the ratio of 60:40 in an ultrasonic cleaning machine which is heated to about 50 degree C. Some times because of the formation of Tin Salts there are white patches on the PCB which could be a major cause of failure of the circuit.

TCE is also getting phased out throughout the world and hence there is a need for an effective substitute which is eco-friendly.

We have developed a special cleaner, which can be used to clean the PCB’s to remove it from the flux contamination very effectively. After the cleaning is over the board has to be dipped in the conventional IPA solution for about two minutes and then air dried to get a PCB free from flux contamination or residues.
PCB Flux Remover

Send Enquiry



Paint Remover For Ferrous And Non Ferrous Metals

An environment friendly Paint remover, specially formulated to remove tough paints and organic coatings from ferrous & non-ferrous metals & alloys.

Works at room temperature. Does not affect the substrate.  

Removes organic coatings, paints like cured epoxy, polyurethane, enamel and lacquer from ferrous & non-ferrous metals and alloys without affecting the substrate.
Paint Remover For Ferrous And Non Ferrous Metals

Send Enquiry



Paint Remover for Plastic & Polymers

A one of its kind product specially formulated to remove paint and organic coatings from most of the plastic, polymer, vinyl & composite surfaces, especially auto parts, without affecting the substrate.

Removes organic coatings, primer & paints like epoxy, polyurethane, enamel and lacquer from plastics without affecting the substrate. Ideally suited for plastic auto parts.
Paint Remover for Plastic & Polymers

Send Enquiry



Peelable Masking Compound

Peelable Masking Compound is a polymer base one pack, hand peelable protective coating, it can be applied by of the method such as brushing, dipping, or spraying.  After coating at least 3 hours are required for completing curing of the coating at room temperature of for fast curing the job is ovened at 700 C temperatures for half an hour.  This product gives outstanding protection against corrosive action of hot alkaline and acid solution.  Peelable Masking Compound can withstand high temperature i.e., up to 3000 C.  Dry film of this compound works as a insulation for electric property and is unaffected by any corrosive action of solution.
Peelable Masking Compound
{short description of image}

Send Enquiry



Rust Remover

An innovative green chemistry product to remove rust & water scale from ferrous metals & alloys.

It is an organic rust remover that removes and cleans rust, water scales & other contaminants from all most all surfaces in general and ferrous metals & alloys in particular.

Very effectively works in removing heavy rust deposits encountered in industries like automobile, railways, marine, aerospace, tools, precision industries.

Handy in removing mild rusts from household metal, tub & tile surfaces, floor rust stains etc., Does not contain any harsh chemicals and is safe to use.

A new rust remover gel specially formulated to remove even the toughest rust with ease. Gel form -hence ideally suited for vertical surfaces – clings, does not sag. Bio-degradable. Easy to use.

Does not contain ozone depleting chemicals and solvents.
Rust Remover

Send Enquiry



Aluminium & Brass Cleaners

An Eco-friendly Aqueous cleaner / brightener for Aluminum & its alloys including High silicon aluminum castings and Brass. It can be used by Immersion, Ultrasonic.

The product is one of its kinds in the market that works at room temperature.

The product is Bio-degradable & meets the standards of safety & environment. Imparts excellent uniform bright finish.
Aluminium & Brass Cleaners

Send Enquiry



Rust Preventive Oil

A unique research product for corrosion prevention of ferrous metals and alloys. R.P.OIL is developed to provide excellent protection against rust & corrosion for Mild Steel & ferrous metals & alloys.

R.P.OIL offers excellent protection for sea shipment consignments.

Contains special anti fungal and anti bacterial additives to keep ferrous surfaces free of fungal & bacterial growth. It does not contain any hazardous additives like nitrates, phosphates etc., Easy to use & safe on all surfaces. Leaves a long lasting protective film. Meets International standards for safety & Quality.
Rust Preventive Oil

Send Enquiry



Pharmaceutical Disinfectant Chemical 

We supply high grade Industrial Disinfectant called Gramicid manufactured by our Principal M/s.U.S.Sterile. It has a proven track record of consistent quality with most of the reputed Indian, Multinationals & Global companies.

Gramicid is a multi-component complex formulation of high concentration Hydrogen Peroxide and Silver in cationic form. Gramicid effectively and completely destroys all microorganisms including viruses, spores, gram positive & gram-negative bacteria, E-Coli, bacteriophages, legionella, salmonella, fungi, yeast and Biofilms. it does not develop any resistance. Use of Gramicid can truly satisfy the requirements of cGMP. Major pharmaceutical companies have taken advantage of Gramicid to replace Halogens, Quats, Phenolics and Aldehydes.

Applications Of Gramicid
Surface Disinfection Gramicid can be used for disinfecting the tanks, manufacturing equipments, pipelines and containers
@ 0.5% to 1%,contact time 2 to 5 min.
Floor & Walls Mopping of floors & walls @ 0.5% to 1% conc.
Indoor Air Quality(IAQ) To maintain the IAQ of manufacturing filling,packing & Raw Material storage areas Gramicid spray @ 3% - 5% concentration by use of Ultra Low Volume Sprayer.(please use 100% plastic made fogger or S.S.made)
Filter Sterlization Inclusive of R. O. Plants, D.M. Plants, Sand, Carbon & Cartridge @200ppm to 500ppm conc.
Water Disinfection Gramicid when added to raw water @15ppm to 10ppm makes water disinfected. The Gramicid treated water should then be passed through R.O. Plant or D. M. Plant.
General Disinfection Gramicid can be used for hand, feet and Gloves disinfection @0.1%
Laundry Disinfection For Aprons, trouser, caps, Linen etc @ 200ppm
Drainage Disinfection @1-2% solution of Gramicid.
Pharmaceutical Disinfectant Chemical

Send Enquiry



Hospitals & Clinical Chemical

The usage of any disinfectant is critically judged from the point of health hazard, irritant, pollutant, narrow spectrum and carcinogenic effects. After studying the various lacunae in the commonly available disinfectant formulations, Our Principal U. S. Steriles has come up with a broad spectrum, versatile ecofriendly formulation to overcome the real threats from microbes.. Particularly the problem of sepsis, which is of prime importance to any hospital.

GRAMICID (Peroxide-silver complex) effectively and completely destroys all microorganisms including viruses, spores, gram positive & gram-negative bacteria, E. Coli, bacteriophages, including legionella, salmonella, fungi, yeast, protozoa and biofilms. It does not develop any resistance. Gramicid eliminates the need of halogen treatment (Cl, Br, I), phenols and aldehydes.

Applications Of Gramicid
Surface Disinfection Gramicid can be used for disinfecting the tanks, manufacturing equipments, pipelines and containers
Floor & Walls @ 0.5% to 1%,contact time 2 to 5 min. Mopping of floors & walls @ 0.5% to 1% conc.
Indoor Air Quality(IAQ) To maintain the IAQ of manufacturing filling,packing & Raw Material storage areas Gramicid spray @ 3% - 5% concentration by use of Ultra Low Volume Sprayer.(please use 100% plastic made fogger)
Filter Sterlization Inclusive of R. O. Plants, D.M. Plants, Sand, Carbon & Cartridge @200ppm to 500ppm conc.
Water Disinfection Gramicid when added to raw water @ 15ppm to 10ppm makes water disinfected. The Gramicid treated water should then be passed through R.O. Plant or D. M. Plant.
General Disinfection Gramicid can be used for hand, feet and Gloves disinfection @0.1%
Laundry Disinfection For Aprons, trouser, caps, Linen etc @ 200ppm
Drainage Disinfection @1-2% solution of Gramicid.
Hospitals Disinfectant Chemical
{short description of image}

Send Enquiry



Effluents Treatment Chemical

GRAMICID – E is a better solution for Effluents Treatment Chemical. Nearly every Industry has problem of toxic waste in one form or another with increasingly stringent regulation and closing of Land fills and deep injection wells. It is GRAMICID E is a complex formulation of two components hydrogen peroxide and silver. Both the biocides components combine together to give a synergetic effect thus obtaining better results even at very low concentration for a longer time. It is highly effective in treating effluent waste produced in any form whether gaseous, solid or liquid. It is used in handling effluents such as 
  • Chemical plants
  • Paper mills
  • Food processing industry
  • Pharmaceutical Manufacturers
  • Textiles units
It generates effluents which contain amines, aldehydes hydroquinones, mercaptans, phenols, reduced sulphur compounds, chlorine, cyanides, chromium, iron, nitrous, oxides and other pollutants. Moreover, GRAMICID E can also be used to treat ponds, lagoons, detoxify soil and contaminated water. 

The features of these are given below: 
  • Detoxification and oxidation of Cyanides & Sulphides.
  • Treatment of effluents containing methyl mercaptan.
  • Prevention of denitrification & bulking.
  • Reduction of COD & BOD values before aerobic or anaerobic digestion of process. It acts as a supplementary to aerobic process.
  • An emergency `or shock load situation, where the supplementary oxygen is required for short time.
  • Increasing the capacity of an activated sludge and its efficiency. it can improve nitrification process.
GRAMICID E is not at all harmful to the environment science the true constituents do not have any detrimental effects on waste water, the reaction results into water and oxygen only, neither of which are harmful. GRAMICID E is also not responsible for causing air pollution.

Effluents Treatment Chemical
{short description of image}

Send Enquiry



Garbage Spray Chemical

Garbage Spray Chemical is a complex formulation of processed Silver, a noble metal and highly concentrated Hydrogen Peroxide. The Hydrogen Peroxide component ensures a rapid germ killing effect and the silver component ensures long lasting effect. Silver is well known for its oligo -dynamic action. The effect of the two is multiplied by a special manufacturing process of Gramicid -E (Synergy). Moreover, its stability enables Gramicid -E to be stored for at least 1 year at normal ambient temperature. It is completely biodegradable in nature when its is de decomposes it produces only oxygen and water. However, Gramiid-E does not pollute the effluent. Make the solution of 1% of G - E and spray on Garbage, completely odor masking within 30 MIN.

The properties of these are as follow:
  • Totally Chlorine free
  • Can be used universally
  • Rapid sterilization
  • No irritation to skin or eyes
  • No alteration to taste of food / substance Non-pollutant and bio-degradable Non-carcinogenic and non-mutagenic
  • Good stability in storage
  • Accurate dosage and easy detection LD50 value is greater than 2854 mg/kg of animal weight
  • Remains effective even at high temperatures
  • Excellent Industrial
  • Biocide
  • Non-staining
  • Non-inflammable
  • Odor-free
  • Neutral pH
  • Long lasting effect
  • No toxic effect reported
  • No resistance developed
A better solution in treating Industrial effluents generates Effluents which contain amines, Aldehydes hydroquinones, mercaptans, phenols, reduced sulphur compounds, chlorine, cyanides, chromium, iron, nitrous, oxides and other pollutants. Excellent for reduction of COD & BOD. It also works as an Odor masking agent can also be used to treat ponds, lagoons, detoxify soil and contaminated water.

We also provide safety manual to our clients which instructs the user to use hand gloves while handling the product.

Packagings: 30 Kgs.
Garbage Spray Chemical
{short description of image}

Send Enquiry



Diesel Engine Cleaners

A three stage process and solution which is: An Innovative Safe Aqueous cleaner, tailor made to effectively remove all kinds of burnt-on carbon, heavy oil / grease, grime, road soils & other deposits from metals & alloys.

Specially designed to clean used Diesel Engine parts in the Re-Manufacturing Industry. It is a safe, Eco-friendly product, designed to clean, degrease and remove carbon generally present in used diesel engine components.

Reaches intricate crevices & cleans effectively without any need for mechanical scrubbing. It is a safe substitute for many hazardous alkaline cleaners. Works effectively on both ferrous & non-ferrous metals & alloys.
Diesel Engine Cleaners
{short description of image}

Send Enquiry



Hydro Flouric Anti-dote Gel

Para Fine-Chem Industries brings to you excellent quality Hydrofluoric Antidote Gel that is used to treat burns caused by hydrofluoric acid. The gel when applied immediately to the burn reduces damage to the tissues or even the bones. This gel is available to you at a very economical rate.

Send Enquiry




SOLVENTS & CHEMICALS

We specialise in supplying Solvents like Iso Propanol, Tri Chloro Ethylene, Xylene, Acetone. These chemicals are available for the use in Electronic Industries for PCB Cleaning applications and other diverse industrial applications. We also have Thinners used  for Degreasing of Sheet Metal Components prior to Powder Coating / painting. We have also developed an Eco-Friendly for soldering flux removing applications.

We offer wide range of PV Solar grade chemicals which includes Sodium Hydroxide Solution, Hydrochloric Acid, Nitric Acid, PoCL 3 used in the process of solar cell manufacturing..

ISO Propyl Alcohol

Iso Propanol is a clear flammable liquid & completely miscible in water.  It is been widely used in the manufacture of Printed Circuit Boards,  Cleaning of PCB to remove flux residue.  Also used as Glass Cleaners and as propellant in Aerosols. It has other innumerable applications for general Industrial cleaning purposes.

SPECIFICATION
MOL.WT - 60.10g/mol 
ASSAY - 99% 
APPEARANSE - CLEAR TO PALE YELLOW
DENSITY - 0.78
FLAMIBILITY  - HIGHLY FLAMMABLE
WATER - LESS THAN 1 %
ISO Propyl Alcohol

Send Enquiry



Tri Chloro Ethylene

A clear, heavy liquid with excellent solvency, Trichloroethylene has no flash point as determined by standard test methods. Its high stability in the presence of common chemical stabilizers and low boiling point permit vapor degreasing with low heat input. Easily recycled, the solvent combines outstanding cleaning power with greater economy.

This material is not ecofriendly we will be discontinuing. This material and coming out weight ecofriendly cleaner which can be substituted for Tri Chloro Ethylene

SPECIFICATION
MOL.WT. - 131.39 g/mol 
ASSAY - 99 .0% 
APPEARANCE - CLEAR LIQUID
DENSITY - 1.45
FLAMMABILITY - NO, CORROSIVE
WATER - LESS THAN 0.5 %
Tri Chloro Ethylene

Send Enquiry



Acetone

Acetone removes organic impurities from substrates and is well suited for greasy/oily contaminations. Its high evaporation rate, however, requires a subsequent cleaning step in e. g. isopropyl alcohol in order to avoid striations on the substrate. Acetone is not well-suited as lift-off medium due to the high fire danger when heated and the trend of particles to be lifted to reabsorb onto the substrate

SPECIFICATION
MOL.WT. - 58.08g/mol  
ASSAY - 99.0 % 
APPEARANCE - CLEAR COLOURLESS LIQUID
DENSITY - 0.79
FLAMMABILITY - HIGHLY FLAMMABLE
WATER - LESS THAN 0.5%
Tri Chloro Ethylene

Send Enquiry



Xylene

Xylene is a solvent with a rather high boiling point of around 140°C. It is sometimes used in the micro electronic industries

SPECIFICATION
MOL.WT. - 106.17g/mol   
ASSAY - 99.0 %   
APPEARANCE - CLEAR  LIQUID
DENSITY - 0.86 
FLAMMABILITY - FLAMMABLE, IRRITANT
WATER - LESS THAN 1 %
Xylene

Send Enquiry



Toluene

Toluene is a clear, water-insoluble liquid with the typical smell of paint thinner. Toluene is a common solvent able to dissolve paints, paint thinners &  silicone sealants

SPECIFICATION
MOL.WT. - 92.14g/mol  
ASSAY - 99.0 %   
APPEARANCE - CLEAR LIQUID
DENSITY - 0.87      
FLAMMABILITY - HIGHLY FLAMMABLE; HARMFUL
WATER - LESS THAN 0.5 %
Toluene

Send Enquiry



N C Thinner

N.C. THINNER is a mixture of esters, glycol, alcohol,  aromatic solvents and ketones suitable diluents to  all nitro products.

N.C. THINNER contains highly flammable solvents. Harmful if inhaled and if absorbed through skin can cause irritation. Always use protective gloves and eye goggles when handling this product. It is highly recommended to provide proper ventilation on working area.

SPECIFICATION
APPEARANCE COLOR – TRANSPARENT LIQUID. 
SPECIFIC GRAVITY – 0.85 + / -.02 KG/LIT.
INITIAL BOILING POINT - 0.2
COPPER CORROSION - NONE
NON – AROMATICS - 50 – 60%
N C Thinner

Send Enquiry



Methyl–Ethyl-Ketone

MEK (Methyl Ethyl Ketone) with its low boiling point can be used as Chemicals additional thinner for spray coating resists, which require a fast resist film drying on the surface. 

SPECIFICATION
MOL.WT. - 72.11g/mol
ASSAY - 99.0 %    
APPEARANCE - CLEAR LIQUID
DENSITY - 0.80    
FLAMMABILITY - HIGHLY FLAMMABLE, IRRITANT
WATER - LESS THAN 1.0 %
METHYL–ETHYL-KETONE

Send Enquiry



METHYL-ISO–BUTYL-KETONE

MIBK, which occurs naturally in food, is a permitted flavouring agent and is used in food-contact materials.  It is also used as an extract on solvent in the manufacture of methyl amyl alcohol and as a denaturant for ethyl alcohol. Because of the irritant effects of MIBK, contact with the skin and eyes should be avoided.  Ingestion of MIBK should not occur with good manufacturing practices. Employees who come into contact with MIBK may not be at  risk, provided that exposure levels in the workplace are kept as low as possible and within the prescribed control limits which are internationally accepted. .

SPECIFICATION
MOL.WT. - 100.16g/mol 
AASSAY - 99.0 %   
APPEARANCE - CLEAR LIQUID
DENSITY - 0.80  
FLAMMABILITY - HIGHLY FLAMMABLE
WATER - LESS THAN 0.5 %
METHYL-ISO–BUTYL-KETONE

Send Enquiry



ETHYL ACETATE

Ethyl Acetate is primarily used as a Solvent  and dilutent & it is low cost, low toxicity, and with bearable odor. It is used to clean circuit boards and also for nail varnish removers. It is also used in paints as an activator or hardener

SPECIFICATION
MOL.WT. - 88.10g/mol  
ASSAY - 99.0 %  
APPEARANCE - CLEAR LIQUID
DENSITY - 0.90 

Coffee beans and tea leaves are decaffeinated using this solvent
SPECIFICATION
FLAMMABILITY - HIGHLY FLAMMABLE
WATER - LESS THAN 0.5 %
ETHYL ACETATE

Send Enquiry




Contact us

Mr. K.G. Vidyasagar
Flat No. 36/37/38, 1st Floor, C Block, Kushal Garden Arcade, Plot No. 1A, IInd Phase, Peenya Industrial Area
Bengaluru, Karnataka - 560 058, India
Telephone:  +(91)-(80)-28372930/ 41241567/ 41241567

Home  |  About Us  |  Our Products  |  Testimonials   |   Site Map  |  Contact Us  |  Enquiry

Member IndiaMART.com© Para-fine Chem Industries, All Rights Reserved. (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited